Clik here to view.
Two-Part Enclosure Designed by Community Member
@Syed wrote: @Oliver_Cohen designed a two-part enclosure, which we 3D printed for testing. This is only one part of the two, but it looks great. It slides into the housing and then there is another...
View ArticleE4000 from Outernet and bias-tee
@andromeda wrote: Hi, I would like know if your E4000 rtl sdr can be switch bias-tee off by software ?What is the command line on linux and from windows ? Thanks in advance. Posts: 1 Participants: 1...
View ArticleClik here to view.
Request- Shorten File Names
@Eric_William_MKme_Te wrote: Just got my Pi and patch antenna running great this week and I noticed when browsing on mobile it is impossible to see what the files are as the large string of numbers at...
View ArticleClik here to view.
EduCase Portable Classroom
@Eric_William_MKme_Te wrote: Some time ago I decided I wanted to incorporate the Outernet receiver into my portable classroom project and I was able to do so with the KU band portable folding dish....
View ArticleClik here to view.
Some Outernet (NooElec) LNA measurements
@cyoung wrote: Here are the results of a test I did on the LNA. I was curious if it met the stated specs or not. Seems like it maybe lives up to its 34 dB gain figure. The test was done using...
View ArticleE4000 and RTL-SDR Dongles
@hobergenix wrote: I purchaser the E4000 receiver, L-Band Amp, Patch Antenna, and RavPower pack fromAmazon. It all appeared to work Ok. The SNR hovered around 2.0 db and did receive severalfiles but...
View ArticleClik here to view.
Problems with Outernet under Raspbian
@N6RFM wrote: Hi, Trying to get Outernet to run on a Raspberry Pi 3 under Raspbian. I'm a Noobie. During the upgrade to "Jessie testing" (to be able to use Librarian), everything goes fine until the...
View ArticleClik here to view.
Connecting but not actually receiving files
@H_Neil wrote: Hi—I've been doing more tests and will post them later---but for now, a general question--I can get a SNR with decibels consistently over 5 and often in the 6 range, though it wavers,...
View ArticleRaspberry Pi Leds
@hobergenix wrote: I know the red led shows the Raspberry PI power status.On power up the yellow led flashes on and off as the board boots up.But after a while the led is on all the time. Posts: 1...
View ArticleClik here to view.
98% of content - weather files
@Yuri wrote: Hello everyone, Sorry I'm novice and ask noob question, but over 1 week I received only 8 photos, ~5 files with text info and many weather files every day. No wikipedia pages or other...
View ArticleClik here to view.
Bluetooth Antenna Add On
@clavo wrote: Anyone have any suggestions on how to mod the C.H.I.P's Wifi/BT board to allow for the addition of an external antenna? I have identified the right pin on the chip (correct me if I am...
View ArticleClik here to view.
Outernet u1 satellite :D
@kalashnikov wrote: from: https://www.clyde.space/our-missions/10-outernet"The initial three Outernet platforms will test much of the functionality of the full constellation. Each spacecraft will...
View ArticleDIY Receiver Kit Delivery
@KH6JAG wrote: I have received no status on the shipment of my kit order. (DIY Receiver Kit, which is available immediately)Please advise or I intend to cancel my order and stop the Paypal payment.Has...
View ArticleSplitting and recombining larger files
@sam_uk wrote: @syed @Abhishek I've been struggling to split the RSS html files into tiny bits, this is going to be a bigger problem. You don't want to read a manual or book in 30 parts.. If you are...
View ArticleClik here to view.
Raspberry Pi 3 Antenna mod for WiFi
@hobergenix wrote: I read about this experiment on the www.amsat.org mailing list.It was performed by Robert Bruninga WB4ARP. He replaced the chip antenna with a simple full sized wire dipole and...
View ArticleClik here to view.
New L-Bank kit user with Raspberry Pi 3 but signal very weak?
@Mark.Birss wrote: Hi Is my LNA faulty ? My signal so weak ? It took quite long to get any signal also Screenshot from 2016-10-29 20-03-18.png1600x900 206 KB Posts: 10 Participants: 3 Read full topic
View ArticleClik here to view.
New user comments
@k4hg wrote: I run the web site where the ham radio APRS data is downloaded. I just got my receiver yesterday and online quickly, it was a surprisingly easy setup process. My first comment on the user...
View ArticleIndex of Images
@donde wrote: I notice for Raspberry Pi 3, two ISO's are shown with same version of 3.1,but different issue dates. Oct 12 and Oct 30. Are they both the same? Or should one use the later date? Why the...
View Article23cm (1250 – 1300 MHz) Loop Yagi
@KH6JAG wrote: Has anyone tried using a 23cm (1250 – 1300 MHz) loop yagi for signal reception? Posts: 1 Participants: 1 Read full topic
View ArticleUpdate CHIP from shell prompt?
@palbeda wrote: I have some software issues with my Chip (stock firmware version 3.0). I have frequent crashes and freezes, so I want to upgrade to 3.1. One other problem I unfortunately have, is that...
View Article